PPWR packaging regulation: guide for brands | BlackSea LOGI

EU packaging regulation (PPWR): what has changed for brands since 12 August 2026

Since 12 August 2026, Regulation (EU) 2025/40, the PPWR, has applied across the EU in place of the old packaging directive. If packaging is designed or made under your brand name, you are as a rule its manufacturer: before placing it on the market you need a conformity assessment, technical documentation and an EU declaration of conformity. The rules that reshape boxes, on empty space, minimisation, recyclability and labels, arrive in stages from 2028, most of them in 2030, so the packaging you design today should already allow for them. General information, not legal advice: for your compliance, consult an expert.

In brief. Since 12 August 2026, the PPWR has applied directly across the EU. If packaging is made under your brand, you are as a rule its manufacturer: you need a conformity assessment, technical documentation and an EU declaration of conformity. Empty space must be minimised from 12 February 2028; minimisation, recyclability and labelling rules follow, mostly from 2030. General information, not legal advice.

General information, not legal advice. For your compliance, consult an expert.

Illustrative study: an all-paper pack taken apart into carton, paperboard insert and band, beside a glass jar
Illustrative AI study

The short answer: what applies now and what comes next

The PPWR is a regulation, not a directive: it has been directly applicable in every Member State since 12 August 2026, with no national transposition (Art. 71). Directive 94/62/EC was repealed on the same day, with a few provisions kept for a transition (Art. 70). It covers packaging placed on the EU market wherever it is made, so a brand based in Switzerland or the UK that sells into the EU is concerned too.

What changed on 12 August 2026 is mainly documentation and traceability. The manufacturer may only place conforming packaging on the market, must carry out the conformity assessment, draw up the technical documentation and the EU declaration of conformity, and keep both for five years for single-use packaging (Art. 15(1)–(3)). Each pack needs an identification element such as a type, batch or serial number, plus the manufacturer’s name and postal address, printed or behind a QR code (Art. 15(5)–(6)). Suppliers must hand over the information the manufacturer needs (Art. 16); importers and distributors have their own checks (Art. 18–19). Lead, cadmium, mercury and hexavalent chromium together may not exceed 100 mg/kg (Art. 5(4)), and food-contact packaging must respect the PFAS limits (Art. 5(5)).

The rules that change the shape of your boxes come later: empty space in sales packaging cut to the minimum necessary from 12 February 2028 (Art. 24(4)), a harmonised material label later than 12 August 2028 (Art. 12(1)), then, from 2030, minimisation, the ban on false volume, recyclability grades and recycled content in plastic (Art. 6, 7 and 10). A box developed now is often reordered in 2028 or 2030: designing it right once costs less than redoing dielines, inserts and tooling later.

What has applied since 12 August 2026

  • Conformity assessment, technical documentation and EU declaration of conformity (Art. 15, 38, 39)
  • Type, batch or serial number on the packaging (Art. 15(5))
  • Manufacturer’s name and postal address, on the pack or via QR code (Art. 15(6))
  • Supplier documentation for the manufacturer (Art. 16)
  • Checks by importers and distributors (Art. 18 and 19)
  • Heavy metals ≤ 100 mg/kg in total; PFAS limits for food contact (Art. 5(4)–(5))
  • Environmental claims only beyond the legal minimum (Art. 14)

Key dates from 2025 to 2038

These dates come from the text of Regulation (EU) 2025/40 on EUR-Lex, checked on 8 November 2026. When an article says “or so many months after the implementing or delegated acts enter into force, whichever is the latest”, the calendar date is the earliest possible one: if the Commission adopts those acts late, the obligation moves with them.

Two points are often misread. The 50% cap on empty space applies to grouped, transport and e-commerce packaging, not to the box on the shelf (Art. 24(1)); for sales packaging the rule is “minimum necessary”, with no percentage (Art. 24(4)). And Article 10(2), the ban on double walls, false bottoms and unnecessary layers, has no date of its own: the Commission’s guidance explains that both paragraphs of Article 10 apply from 1 January 2030, while the current minimisation requirements and the standard EN 13428:2004 remain the reference until the end of 2029 (Art. 70(1)(b)).

According to the same guidance, the general rule that all packaging must be recyclable (Art. 6(1)) has applied since 12 August 2026; until the design-for-recycling criteria apply, the reference remains the previous requirements and standards, such as EN 13430:2004. Penalties are national: each Member State must lay down its rules by 12 February 2027 (Art. 68).

Dates for your planning
DateWhat changesWho it concerns
11 February 2025Entry into force (Art. 71)No obligation yet
12 August 2026The Regulation applies; Directive 94/62/EC repealed, with transitional exceptions (Art. 70–71)Manufacturers (brands), importers and distributors
12 February 2027Deadline for national rules on penalties (Art. 68)Member States
1 January 2028Deadline for the Commission’s design-for-recycling criteria (Art. 6(4))European Commission
12 February 2028Empty space in sales packaging reduced to the minimum necessary (Art. 24(4))Manufacturers of sales packaging
Later than 12 August 2028 (implementing acts still pending on 8 November 2026)Harmonised material label (Art. 12(1))Manufacturers; e-commerce packaging included
1 January 2030 (some rules later)Minimisation and ban on false volume (Art. 10), grades A–C (Art. 6(3)), recycled content in plastic (Art. 7(1)), 50% cap for grouped, transport and e-commerce packaging (Art. 24(1)), Annex V restrictions (Art. 25)Manufacturers; plastic, grouped, transport and e-commerce packaging
1 January 2038Only grades A or B (Art. 6(3))All packaging placed on the market

Manufacturer, supplier, importer, distributor: who does what

The PPWR assigns obligations by role. Four roles matter when you order packaging, and a fifth, the producer, concerns extended producer responsibility. Write down which ones you hold for each product.

Manufacturer

The PPWR does not ask who owns the machines. If you have packaging designed or manufactured under your own name or trademark, you are the manufacturer, even if other marks appear on it (Art. 3(1)(13)(a)). The Commission’s guidance adds that there is only one manufacturer in a supply chain, that the owner of the name or trademark can be assumed to be the manufacturer and that, for sales packaging, it is normally the company that fills it, often the brand itself. A cosmetics brand that has cartons and rigid boxes made in China with its logo is therefore, as a rule, the manufacturer of that packaging. If a contract filler packs your product, put the roles in writing.

One exception concerns micro-enterprises: fewer than 10 people and an annual turnover or balance sheet total of no more than €2 million (Recommendation 2003/361/EC). If the brand is a micro-enterprise and the company supplying the packaging is located in the same Member State, that supplier becomes the manufacturer (Art. 3(1)(13)(b)); for the manufacturer’s obligations in Article 15, Art. 15(12) refers more broadly to a supplier located in the Union. Either way, a factory outside the EU cannot take over that role. Have an expert check how the exception applies to your supply chain.

Supplier

Whoever supplies packaging or packaging materials to the manufacturer (Art. 3(1)(16)) must provide all the information and documentation needed to demonstrate conformity, including what the technical documentation requires, in a language the manufacturer understands (Art. 16(1)). This is the legal basis for asking the production side for material specifications, declarations and test reports.

Importer

The importer is a person established in the EU that places packaging from a third country on the market (Art. 3(1)(17)). According to the Commission’s guidance, a branch without legal personality does not qualify, and for imports the relevant moment is release for free circulation. Before placing packaging on the market, the importer makes sure the manufacturer has carried out the conformity assessment and drawn up the technical documentation, that labelling and documents are in order and that the manufacturer is identified on the pack; the importer then adds its own name and postal address (Art. 18(2)–(3)). An importer that uses its own name or trademark takes on the manufacturer’s obligations (Art. 21).

Distributor and producer

Wholesalers, shops and online retailers that make packaging available are distributors (Art. 3(1)(18)). Before selling, they check that the producer is registered for extended producer responsibility, that the packaging is labelled and that manufacturer and importer details are present (Art. 19(2)); expect your stockists to ask. The producer is a different role from the manufacturer: it is the manufacturer, importer or distributor that first makes packaging available in a Member State, and registration and fees are organised country by country (Art. 3(1)(15), 44 and 45). What stays national is the producer register, the competent authorities and the penalties (Art. 40, 44 and 68).

A Commission proposal of 10 December 2025, COM(2025) 982, would suspend until 1 January 2035 the obligation to appoint an authorised representative for extended producer responsibility in other Member States (Art. 45(3)). On 8 November 2026 it was still under discussion: on 20 October 2026 Parliament adopted its amendments and referred the file back to committee for negotiations with the Council. Until it is adopted, the current text applies.

A typical case

A brand established in Italy has bottles, cartons and gift boxes made in China under its trademark, imports them and sells in Italy and Romania through its e-shop and a few stores. The brand is the manufacturer; if it clears the goods itself, it is also the importer; the stores are distributors. For extended producer responsibility, the brand is normally the producer in Italy and, for e-shop orders delivered to consumers in Romania, in Romania too, where it has to register and, under the current text, appoint an authorised representative (Art. 3(1)(15), 44 and 45(3)). Contracts, Incoterms and who clears customs can change the picture: write down your role for each product and have it confirmed by an expert.

Roles at a glance

  • Manufacturer: has the packaging made under its name or trademark (Art. 3(1)(13))
  • Supplier: provides packaging or materials, and the documentation (Art. 16)
  • Importer: established in the EU, brings packaging from outside the EU (Art. 18)
  • Distributor: resells and checks labelling and registration (Art. 19)
  • Producer: the extended producer responsibility role, registered in each country (Art. 44)
  • One manufacturer per supply chain (Commission guidance)

Technical documentation and the EU declaration of conformity

Before placing packaging on the market, the manufacturer carries out the conformity assessment in Annex VII, internal production control (Module A), or has it done on its behalf, for example by a laboratory, and draws up the technical documentation (Art. 15(2) and 38). If conformity is demonstrated, the manufacturer issues an EU declaration of conformity for each packaging type (Art. 39; Annex VII, point 4). By drawing it up, the manufacturer assumes responsibility for compliance (Art. 39(4)); the Commission’s guidance adds that it may be based on the documentation received from suppliers.

The technical documentation must allow conformity to be assessed and, where applicable, contain: a general description of the packaging and its intended use; the conceptual design, manufacturing drawings and materials of the components; the explanations needed to understand them; the standards and specifications applied; a qualitative description of how the recyclability, minimisation and reuse assessments were carried out; and test reports (Annex VII, point 2). For recyclability, the Commission’s guidance says the PPWR assessment is required only once the design-for-recycling criteria enter into force.

Most of this already exists in a well-run packaging project; it is simply scattered between designer, production and your inbox. For a rigid gift box with a paperboard insert, the file brings together the dieline with internal and external dimensions, the greyboard thickness and the wrapping paper with its grammage, the inks, varnishes, foils and adhesives, the insert drawing, the magnet specification if there is one, the weight of each component, the reasons behind each dimension and the test reports the material suppliers can provide, for example on heavy metals. Collect it at sample stage, not after the goods have shipped.

The declaration follows the model structure of Annex VIII, is written in or translated into the language required by the Member State concerned and is kept up to date (Art. 39(2)). Keep it with the technical documentation for five years after single-use packaging is placed on the market, ten for reusable packaging, and be ready to send everything to an authority within 10 days of a reasoned request (Art. 15(3) and 15(10)). A template is only as good as the data in it: if it does not follow Annex VIII and describe your actual packaging, it will not help you.

Annex VIII: structure of the EU declaration of conformity

  • Unique identification number of the packaging
  • Name and address of the manufacturer and, if any, its authorised representative
  • Statement that it is issued under the manufacturer’s sole responsibility
  • Object of the declaration: identification for traceability and description
  • Union harmonisation legislation complied with, including other acts applied
  • Harmonised standards, common specifications or other specifications used
  • Notified body and certificates, where applicable
  • Additional information, then place and date, name, function and signature

What goes on the pack: now and from 2028

Since 12 August 2026 the packaging must carry a type, batch or serial number or another element that identifies it; when its size or nature does not allow this, the information goes in a document accompanying the product (Art. 15(5)). The manufacturer’s name, registered trade name or trademark and postal address, plus an electronic contact where available, go on the packaging or in a QR code or other data carrier (Art. 15(6)); the importer adds its own details (Art. 18(3)). This information must be legible and must not hide, or be confused with, other mandatory labelling of the product, such as the cosmetic label (Art. 15(7)).

On a folding carton, decide where the identifier goes: a type reference can be printed with the artwork, while a batch code is often added at filling, so keep that panel unvarnished or check that the coding ink holds on the varnish. On a rigid box wrapped in dark or soft-touch paper, inkjet codes can be hard to read or may not adhere: a small label or a dedicated light panel is often the practical answer. Decide early whether name and address are printed or reached via QR code. These are small choices, but changing them once the foil dies and print files are made costs time and money.

From 12 August 2028, or 24 months after the Commission’s implementing acts enter into force if that is later, packaging placed on the market must carry a harmonised, pictogram-based label on its material composition; e-commerce packaging is included, other transport packaging is not (Art. 12(1)). The implementing acts were due by 12 August 2026 (Art. 12(6)), but on 8 November 2026 EUR-Lex listed none: the 24 months had not started, so the label will apply later than 12 August 2028. Check their status before printing long runs. Packaging manufactured or imported before the deadline may still be made available for three years (Art. 12(12)). According to the Commission’s guidance, national sorting labels may not remain alongside the EU label once it applies, and the material abbreviations of Decision 97/129/EC, such as PAP 21, may no longer be used after 12 August 2028, the date on which that Decision is repealed (Art. 70(2)).

In any case, avoid labels and symbols that could mislead about sustainability (Art. 12(8)). Environmental claims on packaging properties regulated by the PPWR are allowed only if they go beyond the legal minimum and state whether they refer to the unit, part of it or all your packaging (Art. 14).

Markings to plan on the artwork

  • Area for the type or batch number, compatible with the surface (Art. 15(5))
  • Manufacturer’s name and postal address, or a QR code (Art. 15(6))
  • Importer’s details, where applicable (Art. 18(3))
  • No overlap with mandatory product labelling (Art. 15(7))
  • Space for the harmonised label in future reprints (Art. 12)
  • Environmental claims only if measurable and beyond the minimum (Art. 14)

Empty space and minimisation: the rules that reshape boxes

Two rules change the size and build of boxes: empty space in sales packaging from 2028 and minimisation from 2030. Neither bans premium packaging; both ask you to explain what every layer and every millimetre is for.

Empty space in sales packaging, from 12 February 2028

Whoever fills sales packaging must reduce empty space to the minimum necessary for the packaging to work, product protection included (Art. 24(4)). The definition is simple: the total internal volume of the sales packaging minus the volume of the packaged product. Filling materials such as paper cuttings, air cushions, bubble wrap, sponge or foam fillers, wood wool and polystyrene chips count as empty space. There is no percentage for sales packaging: according to the Commission’s guidance, compliance is assessed against the existing standard EN 13428:2004, and by 12 February 2032 the Commission will consider ratios for sales packaging, naming cosmetics explicitly (Art. 24(6)).

Minimisation and false volume, from 1 January 2030

The manufacturer or importer must design packaging so that its weight and volume are reduced to the minimum necessary for its functionality (Art. 10(1)), and may not place on the market packaging whose features only increase the perceived volume of the product, including double walls, false bottoms and unnecessary layers (Art. 10(2)). Two exceptions concern Article 10(2) only: designs or shape trademarks protected before 11 February 2025, where the change would affect their novelty or distinctiveness, and products with a protected geographical indication, such as many wines and spirits.

Annex IV lists the criteria that can justify volume, including product protection, logistics, information and “sales for gift purposes, or on the occasion of seasonal events”. Recital 60 adds that marketing and consumer acceptance should not, on their own, justify extra weight or volume. The technical documentation must explain, criterion by criterion, what prevents a further reduction, and simply swapping one material for another is not considered sufficient (Art. 10(4); Annex IV, Part B).

A design check you can run today

A 50 ml bottle that fits in a cylinder of 38 × 125 mm takes up about 142 cm³. In a rigid box with internal dimensions of 120 × 120 × 160 mm (2,304 cm³), about 2,160 cm³ is not product. Designed around the bottle, with a paperboard insert that holds it and a few millimetres of clearance, the same bottle fits a box of about 60 × 60 × 135 mm (486 cm³): empty space drops to about 344 cm³, less than a sixth of the original, and part of it is the insert doing its job. Note that a round bottle in a square box always leaves the corners free: even a perfect fit leaves about a fifth of the cross-section empty. These are illustrative figures, not the legal calculation method.

At the workbench, this means questioning raised platforms that lift the product only to make the box look fuller, double walls whose only job is weight in the hand, and boxes inside boxes. A platform that holds the product, protects a fragile neck or carries the leaflet has a function you can document; one that only fills space will be hard to defend from 2030.

Design check, layer by layer

  • Measure the product with cap, pump or dropper
  • Calculate internal volume minus product volume
  • Write down the function of each layer: protection, retention, information, gift presentation
  • Remove platforms, double walls and layers that only add perceived volume
  • Count void fill, paper or foam as empty space
  • Keep the reasoning and any tests behind each dimension

Recyclability grades and recycled content

All packaging placed on the market must be recyclable (Art. 6(1)). From 1 January 2030, or 24 months after the design-for-recycling criteria enter into force if that is later, it must reach grade A, B or C; from 1 January 2038, only A or B (Art. 6(3)). The criteria are due by 1 January 2028 (Art. 6(4)). Until they are adopted, no one can give your packaging an official grade.

What you can apply now is the logic of Article 6(9): integrated components are assessed with the packaging, separate components are assessed on their own, and no component may hinder the recyclability of the main body. For a paper-based rigid box, look hard at everything that is not paper: magnets, metal or plastic closures, plastic windows, laminations, glitter, flocked or foam inserts. The PPWR does not require mono-material packaging, but every non-fibre element is a question the criteria will ask, so prefer components that come away easily and drop layers that do nothing.

For plastic, Article 7 sets minimum recycled content from 1 January 2030, or three years after the calculation method enters into force if that is later, calculated as an average per manufacturing plant and year: 30% for contact-sensitive packaging mainly made of PET, 10% for contact-sensitive packaging in other plastics, 30% for single-use plastic beverage bottles and 35% for other plastic packaging (Art. 7(1)). Packaging for cosmetic products falls under the “contact-sensitive” definition (Art. 3(1)(49)). Plastic parts below 5% of the total weight of the packaging unit are exempt (Art. 7(5)(b)). If your range uses PET bottles or PP jars, ask now about recycled grades, their colour and clarity and the documents behind them: it is a supply question as much as a design one.

Other materials have no recycled-content targets in the PPWR; the Commission will review the question by 12 February 2032 (Art. 7(15)). Recycled paper therefore remains a brand choice, and if you claim it, keep the figures that support the claim.

Questions to ask about materials

  • Which components are integrated and which are separate? (Art. 6(9))
  • Can magnets, closures and windows be removed by hand?
  • Is the lamination or coating needed, or just habit?
  • For plastic parts: which polymer, what share of the weight, what recycled content? (Art. 7)
  • Which documents can the supplier provide for each material? (Art. 16)

Cartons, rigid boxes, inserts and gift sets in practice

The same rules land differently on each format. Here is what they mean in practice, format by format.

Folding cartons

Usually the simplest case: one paperboard, printed and varnished. Check the fit first, because an oversized carton is what an empty-space assessment notices, then any plastic window, the coding area and where name and address go. For a small glass dropper bottle, a die-cut paperboard support inside the carton often does the job of a separate insert.

Rigid and magnetic boxes

Greyboard wrapped in printed or coloured paper, sometimes laminated, foiled or embossed. The PPWR does not ban them, and Annex IV counts sales for gift purposes among the functions packaging may serve. What changes is the burden of proof: board thickness, box height and every extra layer need a reason. Decide on the magnets at design stage, embedded in the board or placed so they can be removed, because they are a non-fibre component in a fibre box.

Inserts

In the empty-space calculation the insert sits on the empty side: it is not the product. That is fine when it protects and holds; it becomes a problem when it is a block of foam filling a box that is too big. Paperboard and moulded-fibre inserts keep the box within one material family; plastic and foam inserts are plastic parts with their own rules from 2030, unless they weigh less than 5% of the packaging unit (Art. 7).

Gift sets and wine boxes

Seasonal and gift packaging is a recognised function (Annex IV, Part A, point 4), but a coffret for two products still has to be sized for two products. For wine and spirits with a protected geographical indication, Article 10(2)(b) lifts the ban in Article 10(2), false volume included, but not the other requirements, such as minimisation under Article 10(1), recyclability or labelling.

Bottles, jars and single-dose vials

The container is packaging too: glass and plastic bottles, jars and caps are subject to recyclability and, for plastic, to recycled content. Single-use cosmetic, hygiene and toiletry packaging used in hotels and other accommodation for an individual booking, such as shampoo or lotion bottles and sachets around bar soap, is restricted from 1 January 2030 (Art. 25 and Annex V, point 5).

Shipping cartons

If you ship to consumers, the outer carton is e-commerce packaging: from 1 January 2030, or three years after the calculation method enters into force if that is later, its empty space ratio may not exceed 50% (Art. 24(1)). A gift box shipped as it is, without an outer carton, is exempt from that ratio but must still meet Article 10 (Art. 24(5)). Sizing the shipper to the gift box is a design task, not a warehouse afterthought.

Quick check by format

  • Folding carton: fit, plastic window, coding area
  • Rigid or magnetic box: a reason for every layer, a plan for the magnets
  • Insert: protection and retention first, material family second
  • Gift set: sized for its contents; the geographical-indication exception covers only Art. 10(2)
  • Bottle or jar: polymer and recycled content from 2030
  • Shipping carton: 50% empty-space cap from 2030

Checklist for your next packaging order

You do not need to redesign everything this month. You do need to stop ordering packaging you will have to redesign anyway. Use this list when you write the brief and again when you approve the sample.

With BlackSea LOGI, the sample, physical for €120 or on video for €50 (VAT included), is the moment to check dimensions, layers and markings on the real object, before a run that starts at 250 pieces per model. Approving the sample against a written specification also helps keep series production consistent with what you documented, which the manufacturer must ensure (Art. 15(4)).

Before you confirm the order

  • Write down your role for this product: manufacturer, importer, distributor
  • Ask the supplier what documentation it can provide for each material (Art. 16)
  • Freeze the drawings: dieline, internal and external dimensions, insert, weights
  • Run the empty-space check and justify every layer
  • Place batch number, name, postal address and any QR code on the artwork
  • Prepare the technical documentation and the declaration with your adviser
  • Approve the sample against the written specification and keep it
  • Agree quality control and packing for the series
  • Keep documentation and declaration for 5 years for single-use packaging (Art. 15(3))
  • Check the 2028 and 2030 dates before every reprint

What BlackSea LOGI does at design stage, and what it does not

BlackSea LOGI designs and produces packaging from A to Z: bottles and jars, labels, folding cartons, rigid boxes and magnetic gift boxes, inserts, paper bags, film and single-dose vials. Production takes place in China and we follow it from the sample to delivery, as the one company accountable for the project. That matters for the PPWR, because most of the information the Regulation asks for is created at design stage.

In practice, we design around the measured product and question every layer; where protection allows, we propose structures and materials that are easier to separate; we prepare dimensioned drawings and component lists with materials and weights that you or your adviser can use in the technical documentation; we ask the production side for the documentation available for each material and pass on what we receive, with its holder, date and scope; we reserve space on the artwork for batch number, name, address and QR code; and we follow the agreed quality control, packing and shipping of the series.

What we do not do: we are not lawyers and do not give legal advice, we do not certify compliance and we do not describe a box as “PPWR compliant”, not least because several delegated and implementing acts have yet to be adopted. The legal assessment of your role, your technical documentation and your declaration of conformity remains with you and your adviser. General information, not legal advice: for your compliance, consult an expert.

At design stage we

  • Design around the measured product, layer by layer
  • Propose structures and materials that separate more easily
  • Prepare drawings and component lists with materials and weights
  • Request and pass on the documentation available for each material
  • Reserve space for batch number, name, address and QR code
  • Follow the sample, agreed quality control, packing and shipping
  • No legal advice and no compliance certificates

The next step

If your packaging is due for a reorder or a redesign, start from what you already have. Send a designer a photo of the current packaging next to a tape measure, the product measurements and the quantity per model: we will tell you which dimensions, layers, materials and markings deserve a second look, and which questions belong to your compliance adviser.

Message a designer on WhatsApp, or book a 30-minute call if you prefer to go through it together. Projects start at 250 pieces per model; the sample costs €120 as a physical piece or €50 on video. Both prices are VAT included.

Useful to send

  • Photo of the current packaging, with a tape measure
  • Product measurements, including cap, pump or dropper
  • Quantity per model and number of models
  • Countries where you sell
  • Documents you already have from current suppliers

Questions about the PPWR

Yes. Regulation (EU) 2025/40 has applied since 12 August 2026 and is directly applicable in every Member State (Art. 71). Some obligations apply already, such as the manufacturer’s documentation and identification duties (Art. 15); others, such as empty space, recyclability grades and the harmonised label, follow from 2028 onwards.

As a rule, yes: whoever has packaging designed or manufactured under its own name or trademark is the manufacturer (Art. 3(1)(13)(a)). The micro-enterprise exception requires a supplier located in the EU, in the same Member State according to the definition (Art. 3(1)(13)(b) and 15(12)), so a factory outside the EU never takes over that role. Have your specific case checked by an expert.

The Regulation sets the model structure in Annex VIII: identification number, manufacturer, sole-responsibility statement, object of the declaration, legislation applied, standards or specifications, notified body where applicable, additional information and signature. Whatever template you use should follow it, be drawn up for each packaging type and be in the language required by the Member State (Art. 39).

Not as a percentage. For sales packaging, empty space must be reduced to the minimum necessary from 12 February 2028 (Art. 24(4)). The 50% cap applies to grouped, transport and e-commerce packaging from 2030 (Art. 24(1)). By 12 February 2032 the Commission will assess ratios for sales packaging, cosmetics included (Art. 24(6)).

No. The PPWR does not ban these formats. From 2030 it bans features that only increase perceived volume, such as false bottoms (Art. 10(2)), and requires a recyclability grade for all packaging (Art. 6(3)). A well-sized rigid box with a justified insert and a clear plan for the magnets is a sound starting point; the grading criteria are still to come.

Check now that the packaging carries a type, batch or serial number (Art. 15(5)) and the manufacturer’s name and postal address, on the pack or via a data carrier (Art. 15(6)), plus the importer’s details where applicable (Art. 18(3)). The harmonised material label will apply 24 months after the Commission’s implementing acts enter into force, and not before 12 August 2028; on 8 November 2026 those acts had not yet been adopted (Art. 12(1) and (6)).

We design and produce packaging with these requirements in mind and pass on the drawings, specifications and documentation available for your file. Legal compliance stays with the manufacturer, who assumes responsibility by drawing up the declaration of conformity (Art. 39(4)). General information, not legal advice: for your compliance, consult an expert.

Official sources

  1. Regulation (EU) 2025/40 on packaging and packaging waste (PPWR), Official Journal of the EU, L series, 22 January 2025 (opens in a new tab)EUR-Lex

    Recital 60; Articles 3, 5, 6, 7, 10, 12, 14, 15, 16, 18, 19, 21, 24, 25, 38, 39, 40, 44, 45, 68, 70 and 71; Annexes IV, V, VII and VIII

  2. Regulation (EU) 2025/40: document information, amendments and corrigenda (opens in a new tab)EUR-Lex

    Entry into force on 11 February 2025; on the consultation date, no amending act in force and no implementing act on the harmonised label

  3. Commission Notice C(2026) 3702 of 5 June 2026, guidance document for Regulation (EU) 2025/40 (opens in a new tab)European Commission, on EUR-Lex

    Manufacturer and importer; placing on the market; recyclability from 12 August 2026; Article 10 from 1 January 2030; empty space in sales packaging and EN 13428:2004; harmonised labelling

  4. Packaging waste: the PPWR, dates and guidance (opens in a new tab)European Commission, Directorate-General for Environment

    In force since 11 February 2025, applies from 12 August 2026; status of the Environmental Omnibus proposal

  5. Proposal COM(2025) 982 of 10 December 2025 suspending the obligation to appoint an authorised representative for extended producer responsibility (opens in a new tab)EUR-Lex

    Proposed suspension of Article 45(3) until 1 January 2035 (a proposal, not law)

  6. Procedure 2025/0395(COD) on proposal COM(2025) 982 (opens in a new tab)European Parliament, Legislative Observatory

    Status on the consultation date: awaiting Parliament’s first-reading position; on 20 October 2026, amendments adopted and file referred back to committee for interinstitutional negotiations

  7. Commission Recommendation 2003/361/EC on the definition of micro, small and medium-sized enterprises (opens in a new tab)EUR-Lex

    Annex, Article 2(3): micro-enterprise

Consulted on 8 November 2026. Dates and article numbers come from the official text; the Commission’s guidance is not binding, because only the Court of Justice of the EU gives binding interpretations. General information, not legal advice: for your compliance, consult an expert.

Message a designer

Tell us about the product, the format you have in mind and the quantities: a BlackSea LOGI designer reads your message, replies and suggests the next step.

The prepared message ends with the code Ref. SITO-GUIDA-PPWR-EN: it tells us which page you’re writing from. Keep it or delete it.

After your message

  1. 1A designer replies with the questions needed to understand the project.
  2. 2We check format, materials, quantities and destination together.
  3. 3You receive a written quote, with each cost listed separately.
  4. 4After the feasibility review we prepare the sample; series production starts only with your written approval.

Prefer to prepare the brief yourself? FORM (beta)